Signal Processing Systems : Related Signal Processing Products : Evertz - 5601ACO2

2RU Automatic Changeover System with 2 Power Supplies, 2 Power Cords and 2 DB15 Cables

Model: 5601ACO2

Three protected switches select automatic, front panel or GPI activation of changeover
Front panel status LEDs show the health of each of the inputs
Front panel status LEDs show the operational modes of the changeover
Redundant power supply standard
Push button to show cause of last changeover

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The 5601ACO2 Automatic Changeovers are intended for use with two 5601MSC Master Clock/Sync Generators.The 5601ACO2 system uses latching relays to ensure maximum reliability and minimal disruption in the event of any failure.The complete system provides the highest level of security for television station video and time synchronization systems.The 5601ACO2 is a 2RU ACO for all outputs of the 5601MSC.Two power supplies are included as a standard feature, to alleviate any single point of failure concerns.

Three protected switches select automatic, front panel or GPI activation of changeover
Front panel status LEDs show the health of each of the inputs
Front panel status LEDs show the operational modes of the changeover
Redundant power supply standard
Push button to show cause of last changeover
Dual hot swappable power supplied and fans
Hot swappable main board
GPIO input/outputs
Automatic changeover is a voting system based on which source has the most valid signals and that the valid signals on the present master are also on the backup
VistaLINK® control for device configuration and status monitoring (5600ACO2 and 5601ACO2 only)
6 video/sync or other coaxial signals
10MHz frequency reference
Word clock output
DARS and 2 AES
2 Longitudinal (LTC/EBU) timecode outputs
8 SD/HD/3G outputs
2 Analog video test signal output

Spec Sheet available - Yes

AC Voltage: 240 Volts
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Active Power: 40 Watt
Current Draw: 1 Amps
Depth: 11.50 in
Height: 3.54 in
Width: 19.02 in
Product Weight: 16 lbs
Color: Black
Standard: SMPTE ST 12-1 frame rate set by 5601MSC or IRIG-B
Inputs: 2 per 5601MSC
Outputs: 2
Signal Level: Set in 5601MSC
Coaxial Inputs and Outputs:
Type: Depends on signal connected from 5601MSC
HD-SDI, SD-SDI, Analog TG, AES, DARS, bi-level or tri-level sync, colour black, 10MHz, Word Clock:
Number: 16 groups each consisting of two inputs and one output
Connector: BNC per IEC 61169-8 Annex A
GPI1: Master select in Manual GPI control mode
Low: Selects Master A
High: Selects Master B
GPI2: Future use
2 GPI outputs connected from Master B through AUXI/O B:
Changeover is a voting system based on which source has the most good signals and that the good signals on the current master are also present on the backup master. The input signals are considered good according to the following criteria:
Video: Level below 70 IRE
Sync: H timing detect
10MHz: 3dB level below 0.3V p-p
DARS: Sync word error
LTC: Level below 0.3V p-p Incorrect sync word

2RU Automatic Changeover System with 2 Power Supplies, 2 Power Cords and 2 DB15 Cables 160 kb - Data Sheet

Project List

Products

2RU Automatic Changeover System with 2 Power Supplies, 2 Power Cords and 2 DB15 Cables

Model: 5601ACO2

Contact

Solutions

Insights

About

Privacy Policy

Terms & Conditions

Copyright © 2025 A-V Services, Inc. | All Rights Reserved | Powered By Chatter Creative